Beier electronic speed controller UFR-1230

The UFR-1230 at a glance:

• Drive controller for DC brush motors
• Especially for vehicles / trucks
• Supply voltage: 6 - 18 V
• Max. Motor current: 30 A
• Powerful BEC with 5.2 V, 3 A
• 8 switching outputs for the lighting
• Optional load regulation, cruise control, braking functions
• Further options via the Windows software "Drive-Teacher" adjustable

description
The UFR-1230 has been specially developed for RC model vehicles to control DC motor brush motors.

The realistic and dynamic control of the vehicle controller guarantees the highest driving and marshalling pass with extensive additional options.

Due to the various (optional) adjustment possibilities, the driving controller can be easily and individually adapted to the most varied model requirements and driving characteristics. All settings are made quickly and easily via DIP switches or with the help of the "Drive-Teacher" software.

The lighting of the model can be connected directly to the mobile controller at 8 light outputs. The travel controller has an extra output for connection of the IR transmitter for the light module SM-IR-16-2.

All lighting and additional functions of the cruise control can be controlled via Nautic and Multiswitch modules.

The driving controller has the following features:

• Supply voltage: 6 - 18 V
• Max. Motor current 30 A (short-term 60 A)
• PWM clock frequency 20 or 40 kHz
• 8 switching outputs for the illumination (for example, brake light, backlight, parking light, low beam, turn signal, curve lights)
• Powerful BEC with 5.2 V, 3 A continuous current (short circuit proof)
• 3 Proportional inputs (gas channel, steering, control channel)
• 2 proportional outputs (output for sound module, steering servo)
• Additional functions can be controlled via Nautic and Multiswitch modules
• Failsafe in the event of a reception fault (engine stop)
• Start-up protection when switching on
• Output for IR-diode for light module SM-IR-16-2 in trailer / trailer
• Battery voltage monitoring
• temperature monitoring
• Short circuit protection motor end stage

Options selectable via DIP switch:

• Load regulation on / off
• Cruise control on / off
• Brake function on / off
• Handbrake function on / off
• Choice of battery type: LiPo / other type

Set-up function (setup) for gas channel on / offAdditional functions can be set via the data cable K-USB-2 (optionally available) and the Windows software "Drive-Teacher":

• firmware update
• diagnosis
• channel inversion
• Disconnection of the undervoltage monitoring
• Reduction of the return speed to 50%
• Choice of PWM clock frequency 20 or 40 kHz (for bell-type induction motors)
• Adjustment of load regulation
• Activation / adjustment of the degree of inertia
• Activation / adjustment of the inertia
• Adjustment of the handbrake hardness
• Adjustment of the gas curve
• Configuration of the switching outputs (output types, brightness, xenon effects, etc.)
• Configuration of the light switch (switchable via control channel)
• Configuration of the control channel
• Configuration of Nautic / Multiswitch Modules
• Configuration of the servo outputs of the light module SM-IR-16-2
• The driving controller is supplied with a standard configuration (see screenshots in the operating instructions) and is ready for operation. The data cable is therefore only required if one of the above options is to be set or changed. The Windows "Drive-Teacher" software can be downloaded free of charge here: Download (2 MB)

For further information, refer to the operating instructions (PDF).

Technical specifications

• Supply voltage (Ub): 6 - 18 V DC voltage
• Power consumption: retentive current: approx. 40 mA
• Motor current: max. 30 A continuous current, 60 A short-term (1 minute)
• BEC voltage: 5.2 V
• BEC current: max. 3 A continuous current, 5 A short-term (10 seconds)
• Proportional inputs: 3 pieces (1,000 - 2,000 ms)
• gas channel
• Steering channel control channel
• Proportional outputs: 2 pieces (1,000 - 2,000 ms)

Output for sound module

• Servo output for steering servo
• Switching outputs: 8 pieces (npn - open collector), max. 1.5 A per output, the total current of all outputs must not exceed 3.0 A.

Protection functions:

• Short circuit protection motor end stage
• Short circuit protection switching outputs
• Short circuit protection BEC
• temperature monitoring
• Battery undervoltage monitoring
• Start-up protection when switching on
• Failsafe for proportional inputs

Other interfaces:

• Programming interface for data cables
• Connection for IR-diode SM-IR-16-2

Connecting cable:

• Battery connection: 2 x 2,5 mm², length approx. 25 cm (with Tamiya socket)
• Motor connection 2 x 2,5 mm², length approx. 25 cm
• Servocabel for connection to receiver: 3 x 0,14 mm², length approx. 30 cm

Permissible ambient temperature: 0 - 60 ° C

• Permissible relative humidity: Max. 85%
• Dimension: 65 x 45 x 23 mm
• Weight: 75 g

Delivery:

• Driving controller UFR-1230
• Operating instructions (German)
• Flat ribbon cable (40 cm) for connecting the switching outputs

Recommended accessories:

• Data Cable K-USB-2 (32435)
• Terminal block AKL-10 (32779) or AKL-10-W (32780)